The short version of chromatogram fits in a sentence. The long version — which is the one that helps — is below.
This page was last updated on 2026-03-04 and is reviewed periodically as new material appears.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
The primary medical treatment of acromegaly is to use somatostatin analogues – octreotide (Sandostatin) or lanreotide (Somatuline). Somatostatin analogues are also sometimes used to shrink large tumors before surgery. Because octreotide inhibits gastrointestinal and pancreatic function, long-term use causes digestive problems such as loose stools, nausea, and gas in one-third of people. In addition, approximately 25 percent of people with acromegaly develop gallstones, which are usually asymptomatic. In some cases, octreotide treatment can cause diabetes because somatostatin and its analogues can inhibit the release of insulin. With an aggressive adenoma that is not able to be operated on, there may be a resistance to octreotide in which case a second-generation SSA, pasireotide, may be used for tumor control. However, insulin and glucose levels should be carefully monitored as pasireotide has been associated with hyperglycemia by reducing insulin secretion.
Förster resonance energy transfer (FRET)-based Cl indicators consist of two fluorescent proteins, Cyan fluorescent protein (CFP) and YFP connected via a polypeptide linker. This allows ratiometric Cl− measurements based on the Cl− sensitivity of YFP and Cl− insensivity of CFP. Clomeleon and Cl− Sensor are FRET-based Cl indicators that allow ratiometric non-invasive monitoring of chloride activity in living cells.
12(S)-HETE and 12(S)-HpETE stimulate the dilation of rat mesenteric arteries; 12(S)-HETE stimulates the dilation of coronary microvessels in pigs and the mesenteric arteries of mice, one or more of these three metabolites are implicated in the vasodilation of rat basilar artery, 12(R)-HETE and to a slightly lesser extent 12(S)-HETE constrict the renal artery of dogs and 12-HETE (stereoisomer undetermined) is implicated in the angiotensin II-induced arterial hypertension response of human placenta. The vasodilating effect on mouse mesenteric arteries appears due to 12S-HETE's ability to act as a thromboxane receptor antagonist and thereby block the vasoconstricting actions of thromboxane A2. These results indicate that the cited metabolites have dilating or constricting effects that depend on the arterial vascular site and or species of animal examined; their role in human blood pressure regulation is unclear. Excessive 12-HETE production is implicated in psoriasis. 5-Hydroxyeicosatetraenoic acid 15-Hydroxyeicosatetraenoic acid
5-Oxo-eicosatetraenoic acid (i.e. 5-oxo-6E,8Z,11Z,14Z-eicosatetraenoic acid; also termed 5-oxo-ETE and 5-oxoETE) is a nonclassic eicosanoid metabolite of arachidonic acid and the most potent naturally occurring member of the 5-HETE family of cell signaling agents. Like other cell signaling agents, 5-oxo-ETE is made by a cell and then feeds back to stimulate its parent cell (see Autocrine signaling) and/or exits this cell to stimulate nearby cells (see Paracrine signaling). 5-Oxo-ETE can stimulate various cell types particularly human leukocytes but possesses its highest potency and power in stimulating the human eosinophil type of leukocyte. It is therefore suggested to be formed during and to be an important contributor to the formation and progression of eosinophil-based allergic reactions; it is also suggested that 5-oxo-ETE contributes to the development of inflammation, cancer cell growth, and other pathological and physiological events.
When genotypes grown together in a diverse population have different profiles of resource use they complement each other in the exploitation of the limiting resource and therefore are subject to smaller between-plant competition. In case of disease or environmental change some plants will take over when others fail. Yield stability over years and environments can be better than pure lines due to compensation. Participatory plant breeding (PPB) methods represent alternatives aimed to improve local adaptation breeding, to promote genetic diversity, to empower farmers and rural communities. In PPB farmers are actively participating in developing new cultivars or populations, e.g. by performing selection.
Sources: en.wikipedia.org
Sensory evoked potentials (SEP) are recorded from the central nervous system following stimulation of sense organs, for example, visual evoked potentials elicited by a flashing light or changing pattern on a monitor, auditory evoked potentials by a click or tone stimulus presented through earphones), or tactile or somatosensory evoked potential (SSEP) elicited by tactile or electrical stimulation of a sensory or mixed nerve in the periphery. Sensory evoked potentials have been widely used in clinical diagnostic medicine since the 1970s, and also in intraoperative neurophysiology monitoring (IONM), also known as surgical neurophysiology. There are three kinds of evoked potentials in widespread clinical use: auditory evoked potentials, usually recorded from the scalp but originating at brainstem level; visual evoked potentials, and somatosensory evoked potentials, which are elicited by electrical stimulation of peripheral nerve. Examples of SEP usage include:
Cardona completed his PhD at the University of Barcelona (2000–2005), where he studied developmental biology. He then undertook postdoctoral research on Drosophila neuroanatomy at UCLA (2005–2008). Between 2008 and 2011, Cardona was a Group Leader at the Institute of Neuroinformatics, jointly run by the University of Zurich and ETH Zurich. During this period, he developed computational and image-processing methods for neural circuit reconstruction and co-founded two influential open-source platforms that have become widely adopted in the neuroscience community. Cardona joined the Howard Hughes Medical Institute (HHMI) Janelia Research Campus in 2012, serving as Group Leader until 2019. In 2019, he was appointed Programme Leader at the MRC Laboratory of Molecular Biology and Professor at the University of Cambridge, where he leads research on whole-brain connectomics, circuit development, and structure–function relationships in neural systems.
A NAD⁺-II class riboswitch, termed mini-NAD⁺-II, was first identified through iterative covariance model (CM) searches against representative bacterial genomes in the Genome Taxonomy Database. Mini-NAD⁺-II riboswitches lack the P1a stem and instead fold into a simple H-type pseudoknot, a compact RNA tertiary structure. The conserved nucleotides essential for tertiary contacts and specific recognition of the NMN moiety are retained, as is an A-rich tract following the P1 stem that likely forms a minor groove triplex. Mini-NAD⁺-II riboswitches lack the P1a stem and instead fold into a simple H-type pseudoknot, a compact RNA tertiary structure. The conserved nucleotides essential for tertiary contacts and specific recognition of the NMN moiety are retained, as is an A-rich tract following the P1 stem that likely forms a minor groove triplex. The potential for base pairing with the adjacent Shine–Dalgarno sequence is also retained, suggesting a conserved mechanism of translational regulation.
1.4 Alternatively some books provide the following formula and is called Reticulocyte Index (RI): Whereas normal reticulocytes lose their RNA within 24 hours, a severely anemic patient with a full erythropoietin response will release reticulocytes that take from 2-3 days to lose their RNA. This has the effect of raising the reticulocyte count simply because reticulocytes produced on any single day will spend more than 1 day in circulation as reticulocytes and, therefore, will be counted for 2 or more days. The simplest method for correcting the reticulocyte count, to obtain a more accurate daily production index, is to divide the corrected count by a factor of 2 (or multiply with ½) whenever polychromasia (the presence of immature marrow reticulocytes or "shift" cells) is observed on the smear or the immature fraction on the automated counter is increased. R I = R e t i c P e r c e n t a g e ∗ H e m a t o c r i t N o r m a l H e m a t o c r i t ∗ 0.5 {\displaystyle RI=ReticPercentage*{Hematocrit \over NormalHematocrit}*0.5} → R I = 5 ∗ 25 45 ∗ 0.5 =
Sources: en.wikipedia.org
Anoop's father, who was the Minister for Food and Civil Supplies, died on 30 October 2011. Following this, Anoop was nominated by the Kerala Congress (Jacob) and UDF to contest from the Piravom assembly seat previously represented by his father. His father had lost the sitting seat in 2006 elections and recaptured it in 2011 election by a margin of 157 votes. Against Anoop Jacob, CPI(M)–led LDF once again fielded M. J. Jacob, who had won against T. M. Jacob in 2006 and lost in 2011. Since the result of Piravom by-election mattered heavily to the ruling UDF who had a slender margin of 1 seat in the Legislative assembly over LDF, the constituency witnessed intense campaigning from both sides. Election was held on 17 March 2012 and results were announced on 21 March 2012. Anoop Jacob won the by-election by a significant margin of 12,071 votes. He was sworn in as an MLA on 22 March 2012. Anoop took oath as the Minister for Food & Civil Supplies on 12 April 2012 and occupied office in the North Block of the Kerala Secretariat; both portfolio & office last held by his departed father.
Smith was hired to become the defensive quality control coach for the Tennessee Titans in 2011 under new head coach Mike Munchak. Smith then became the offensive quality coach the following season. In 2013, Smith was promoted to the assistant offensive line and assistant tight ends coach. Munchak was fired after the 2013 season and new head coach Ken Whisenhunt retained Smith as the assistant tight ends coach. Midway through the 2015 season, Whisenhunt was fired and replaced by tight ends coach Mike Mularkey. Mularkey was kept as head coach for the 2016 season and Smith was promoted to the new tight ends coach. When Mularkey was fired after the 2017 season, new head coach Mike Vrabel kept Smith as the tight ends coach for 2018. On January 21, 2019, Smith was promoted to offensive coordinator, replacing Matt LaFleur, who departed to become head coach of the Green Bay Packers two weeks prior. In his first year as offensive coordinator, Smith oversaw the highest-scoring Titans team in 16 years, with Derrick Henry, Ryan Tannehill, and Jonnu Smith having career years. Smith was praised for his play-calling in the Titans' 28–12 road victory over the top-seeded Baltimore Ravens in the AFC Divisional Round. In 2020, the Titans ranked fourth in scoring and second in total yards.
The final step in the non-mevalonate pathway is carried out by the enzyme 4-hydroxy-3-methylbut-2-enyl diphosphate reductase, which gives a mixture of dimethylallyl pyrophosphate and isopentenyl pyrophosphate in the ratio of five to one. The products are then used in terpenoid biosynthesis. HMB-PP is an essential metabolite in most pathogenic bacteria including Mycobacterium tuberculosis as well as in malaria parasites, but is absent from the human host. HMB-PP is the physiological activator ("phosphoantigen") for human Vγ9/Vδ2 T cells, the major γδ T cell population in peripheral blood. With a bioactivity of 0.1 nM it is 10,000-10,000,000 times more potent than any other natural compound, such as IPP or alkyl amines. HMB-PP functions in this capacity by binding the B30.2 domain of BTN3A1. 4-hydroxy-3-methylbut-2-enyl+pyrophosphate at the U.S. National Library of Medicine Medical Subject Headings (MeSH)
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.