The short version of retention time fits in a sentence. The long version — which is the one that helps — is below.
This page was last updated on 2026-06-28 and is reviewed periodically as new material appears.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Antibody mimetics are organic compounds, like antibodies, that can specifically bind antigens. They consist of artificial peptides or proteins, or aptamer-based nucleic acid molecules with a molar mass of about 3 to 20 kDa. Antibody fragments, such as Fab and nanobodies are not considered as antibody mimetics. Common advantages over antibodies are better solubility, tissue penetration, stability towards heat and enzymes, and comparatively low production costs. Antibody mimetics have been developed and commercialized as research, diagnostic and therapeutic agents. BAU (binding antibody unit, often as BAU/mL) is a measurement unit defined by the WHO for the comparison of assays detecting the same class of immunoglobulins with the same specificity.
Human chorionic gonadotropin injection is extensively used for final maturation induction in lieu of luteinizing hormone. In the presence of one or more mature ovarian follicles, ovulation can be triggered by the administration of HCG. As ovulation will happen between 38 and 40 hours after a single HCG injection, procedures can be scheduled to take advantage of this time sequence, such as intrauterine insemination or sexual intercourse. Also, patients that undergo IVF, in general, receive HCG to trigger the ovulation process, but have an oocyte retrieval performed at about 34 to 36 hours after injection, a few hours before the eggs actually would be released from the ovary. As hCG supports the corpus luteum, administration of hCG is used in certain circumstances to enhance the production of progesterone. Several vaccines against human chorionic gonadotropin (hCG) for the prevention of pregnancy are currently in clinical trials.
In biochemistry, control coefficients are used to describe how much influence a given reaction step has on the flux or concentration of the species at steady state. This can be accomplished experimentally by changing the expression level of a given enzyme and measuring the resulting changes in flux and metabolite levels. In theory, any observables, such as growth rate, or even combinations of observables, can be defined using a control coefficient; but flux and concentration control coefficients are by far the most commonly used. The simplest way to look at control coefficients is as the scaled derivatives of the steady-state change in an observable with respect to a change in enzyme activity (ei for each species i). For example, the flux control coefficients (C Jei, where J is the reaction rate) can be written as: C e i J = d J d e i e i J = d ln J d ln e i ≈ J % e i % {\displaystyle C_{e_{i}}^{J}={\frac {dJ}{de_{i}}}{\frac {e_{i}}{J}}={\frac {d\ln J}{d\ln e_{i}}}\approx {\frac {J\%}{e_{i}\%}}}
Apoptosis in HeLa cells is inhibited by proteins produced by the cell; these inhibitory proteins target retinoblastoma tumor-suppressing proteins. These tumor-suppressing proteins regulate the cell cycle, but are rendered inactive when bound to an inhibitory protein. HPV E6 and E7 are inhibitory proteins expressed by the human papillomavirus, HPV being responsible for the formation of the cervical tumor from which HeLa cells are derived. HPV E6 causes p53, which regulates the cell cycle, to become inactive. HPV E7 binds to retinoblastoma tumor suppressing proteins and limits its ability to control cell division. These two inhibitory proteins are partially responsible for HeLa cells' immortality by inhibiting apoptosis to occur.
Sources: en.wikipedia.org
Her research involves structural characterization of biopolymers using mass spectrometry-based techniques, such as liquid chromatography-mass spectrometry, thin-layer chromatography-mass spectrometry, Fourier-transform ion cyclotron resonance mass spectrometry, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, microfluidic capillary electrophoresis-mass spectrometry, and ion mobility spectrometry-mass spectrometry. She was one of the first scientists to characterize glycoconjugates with tandem mass spectrometry. Her 1988 article has been cited over two thousand times. She participated in the Human Proteome Project, the SysteMHC Atlas project, and the Minimum Information Required for a Glycomics Experiment (MIRAGE) project.
Bacillus virus φ29 (bacteriophage φ29) is a double-stranded DNA (dsDNA) bacteriophage with a prolate icosahedral head and a short tail that belongs to the genus Salasvirus, order Caudovirales, and family Salasmaviridae. They are in the same order as phages PZA, φ15, BS32, B103, M2Y (M2), Nf, and GA-1. First discovered in 1965, the φ29 phage is the smallest Bacillus phage isolated to date and is among the smallest known dsDNA phages. φ29 has a unique DNA packaging motor structure that employs prohead packaging RNA (pRNA) to guide the translocation of the phage genome during replication. This novel structure system has inspired ongoing research in nanotechnology, drug delivery, and therapeutics. In nature, the φ29 phage infects Bacillus subtilis, a species of gram-positive, endospore-forming bacteria that is found in soil, as well as the gastrointestinal tracts of various marine and terrestrial organisms, including human beings.
Pregnant women are advised to pay attention to the foods they eat during pregnancy to reduce the risk of exposure to substances or bacteria that may be harmful to the developing fetus. This can include potentially harmful pathogens such as listeria, toxoplasmosis, and salmonella. Intake of large amounts of retinol has been linked to birth defects and abnormalities. During pregnancy, a woman's mass increases by about 12 kg (26 lb). The European Food Safety Authority recommends an increase of 300 mL per day compared to the normal intake for non-pregnant women, taking the total adequate water intake (from food and fluids) to 2,300 mL, or approximately 1,850 mL/ day from fluids alone.
Loading buffers often contain anionic dyes that are visible under the visible light spectrum, and are added to the gel before the nucleic acid. Tracking dyes should not be reactive so as not to alter the sample, and move down the gel with the DNA or RNA sample. Commonly used color markers include Bromophenol blue, Cresol Red, Orange G and Xylene cyanol. Xylene and bromophenol blue are the most commonly used dyes. Generally speaking, Orange G migrates faster than bromophenol blue, which migrates faster than xylene cyanol, but the apparent "sizes" of these dyes (compared to DNA molecules) varies with the concentration of agarose and the buffer system used. For instance, in a 1% agarose gel made in TAE buffer (Tris-acetate-EDTA), xylene cyanol migrates at the speed of a 3000 base pair (bp) molecule of DNA and bromophenol blue migrates at 400 bp. However, in a 1% gel made in TBE buffer (Tris-borate-EDTA), they migrate at 2000 bp and 250 bp respectively.
Subject of research: synthesis of organophosphorous and organoelement compounds, study of their spatial and electronic structure, intramolecular electronic interactions, reaction capacity and mechanism of reactions. Arkady N. Pudovik corresponding member of Russian Academy of Science worked at this department since its opening (1948) until his death (February 2006) he was the founder of the department of High Molecular and Organoelement Compounds and held the position of Head of department until 1987. Current head of the Department – Corresponding Member of the Academy of Sciences of the Republic of Tatarstan, Professor Vladimir I. Galkin, doctor of Science in chemistry. The Department conducts research in the following fields:
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.